Note the Operating Instructions! Attention, outside case temperature may be hot! The physical and chemical properties of your load e. Please note that the Memmert ovens described here are not explosion-proof they do not conform to Occupational Association Regulation VBG They are therefore unsuitable for drying, evaporating or burning-in of enamels or similar substances whose solvent may form an inflammable mixture together with air. Excessive dust or aggressive vapors in the interior of the oven may result in sediments within the oven and cause short circuits or damage to the electronic parts.
Therefore dust and aggressive vapors should be kept from the oven. If the ovens have to be carried, at least 2 persons are required for this mode of transport depending on size Model to or at least 4 persons Model and Before current-connection please compare label on the oven and instructions of your local current supplier.
This equipment is intended for operation on a supply system with a system impedance. Z max at the transfer point building connection which does not exceed 0. The user has to ensure that the equipment is being operated on a supply system which meets this requirement.
If necessary, details of the system impedance can be obtained from the local power supply authority. Memmert is using stainless steel Spec. The oven can be set up on the floor or on a table bench , model - on a subframe. Ensure at least mm clearance between back of oven and wall. The distance between ceiling and oven should not be less than mm and the minimum wall spacing to the sides is 80 mm. The model is movable. The front castors are lockable by means of a fixation.
In order to assure stability, the front castors must always be adjusted to the front side of the oven for locking. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Serial adjustable overheat control in compliance with DIN Class 3. Class Aim of Scope of Safety Safety protection protection device measures No risk liable to TWB adjustable temperaure limiter 2 originate from the automatically shuts off the Special safety Protection of oven in the event oven if the user selected measures required the oven, the of a fault temperature limit is exceeded.
You can only view or download manuals with. Sign Up and get 5 for free. Setting the temperature Selecting the operating mode Normal operation Timer operation Temperature monitor and protection devices Temperature limiter TB Monitor relay Guidelines for sterilisation Steriliser cassettes Error messages CE Conformity Declaration Address and customer service You have purchased a technically fully proven product which has been produced in Germany with the use of high-grade materials and the application of the latest manufacturing techniques; it has been factory tested for many hours.
Observation of the Operating Instructions is necessary for faultless operaton and for any possible claims under warranty. If these Instructions are disregarded, all claims under warranty, guarantee and indemnification are excluded! The product is intended for the sterilisation of medical products with dry heat using hot air at atmospheric pressure.
Installation facilities accessories. The oven can be placed on the floor or on a bench working surface. The spacing from the back of the oven to the wall should be at least 15 cm.
The spacing to the ceiling must not be less than 20 cm and that at the side to the wall not less than 8 cm. Generally it is essential to have adequate air ventilation around the oven. Information on accessories will be found in our leaflet or on our internet page www. Please note the installation instructions for our accessories.
Ovens models to can be wall-mounted using the wall bracket. The wall bracket is factory-fitted with a fire-resistant plate. The size and length of the screws used and of the corresponding dowel plugs depend on the total weight oven plus load and vary with the condition of the wall. Two ovens of the same model size can be stacked on each other. Note that the oven with the lower working temperature must always be placed at the bottom. When the oven is started up for the first time, it should be supervised continuously until steady conditions have been reached.
Severe vibrations during transport may cause movement of the temperature probe in its holder inside the chamber. Note therefore that before the first start-up the temperature probe should be checked for its correct position and, if necessary, carefully aligned in its mounting see ill.
Full consideration must be given to the physical and chemical properties of your load e. Please note that the MEMMERT ovens described here are not explosionproof they do not conform to the Industrial Association Specification VBG 24 and are therefore not suitable for drying, evaporating and burning-in of paints, enamels or similar materials whose solvents may produce an inflammable mixture with air. Large amounts of dust or corrosive fumes inside the oven chamber or in the surroundings of the equipment may produce deposits within the oven and lead to short-circuits or damage the electronics.
It is therefore important that adequate precautions are taken against excessive dust or corrosive fumes. In order to ensure proper air circulation inside the chamber, there must be sufficient spacing of the load inside the oven. Do not place any load on the floor, against the side walls or underneath the ceiling of the chamber heating ribs. In order to ensure optimum air circulation the shelves must be so inserted that the air spacings between door, shelf and rear chamber wall are approximately equal.
With unfavourable loading too closely spaced and completely opened ventilation it is possible that the set temperature may be reached only after a longer period of time. The oven load has to be checked carefully for its chemical compatibility with the above materials. This product is intended to operate on a supply network with a system impedance Zmax at the transfer point building connection of 0.
The user has to ensure that the product is only operated on an electrical supply network which meets these requirements. If necessary, details of the system impedance can be obtained from the local electricity supply authority. Any work involving opening up the oven must only be carried out by a suitably qualified electrician! After a failure of the supply, operation is continued with the same parameter settings.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up.
0コメント